GreenYes Archives
[GreenYes Archives] - [Thread Index] - [Date Index]
[Date Prev] - [Date Next] - [Thread Prev] - [Thread Next]

Re: [GreenYes] Re: plastics recycling education
Anne-

 During polymerization of the ethylene chains they are processed
differently. To keep the gooey/runny rubric, it's kind of like making maple
syrup -- the longer it boils the denser (i.e. gooey) it gets.

                                                Peter

----- Original Message -----
From: "Anne Morse" <AMorse@Co.Winona.MN.US>
To: "'Peter Anderson'" <anderson@recycleworlds.org>; "melissa terry"
<melissaterry@yahoo.com>; <greenyes@grrn.org>
Sent: Monday, January 07, 2002 4:22 PM
Subject: RE: [GreenYes] Re: plastics recycling education


And what is it exactly that makes one formulation gooey and another runny?
Is there an additive?



-----Original Message-----
From: Peter Anderson [mailto:anderson@recycleworlds.org]
Sent: Monday, January 07, 2002 4:04 PM
To: melissa terry; greenyes@grrn.org
Subject: [GreenYes] Re: plastics recycling education


In answer to your question below about the different melt indices of HDPE:
polyethylenes such as HDPE, PP and LDPE can be either blow mold or injection
grade resin.

Blow mold grades have something called their "melt index" less than one
(sometimes referred to as fractional melts), and injection grades more than
one, but typically >10.

In simple language, melt flow is just a measure of how gooey vs. runny the
resin is.  To hold in its liquid state against the sides of a bottle mold,
the resin must be gooey.  To flow easily into and through the cavity of a
mold to make a cap, yogurt cup or ice cream pail, it must be runny.

Except for very low end applications such as flower pots and unrated plastic
lumber, the end markets will only accept HDPE that is either blow or
injection -- the two cannot be mixed.  And for applications the melt flows
will need to be only low or very high flows to be accepted.

In retrospect, it is unfortunate that the original SPI codes assigned no. 2
to both blow and injection, but there you go, hey?

                                                Peter



----- Original Message -----
From: "melissa terry" <melissaterry@yahoo.com>
To: "Peter Anderson" <anderson@recycleworlds.org>; <greenyes@grrn.org>
Sent: Monday, January 07, 2002 3:24 PM
Subject: plastics recycling education


dear recyclers,

while we're on the sticky subject of plastics, does
anyone know if there is ANY educational material
available out there that explains the difference
between blow-molded and injection-molded plastics?

i have visted with the american plastics/chemistry
council and with the napcor folks to no avail. i'm
specifically looking for a poster or something to help
explain why, because of their different markets, we
cannot accept all #1's and #2's in our program at this
time.

any leads would be greatly appreciated!

cheers,
melissa terry

__________________________________________________
Do You Yahoo!?
Send FREE video emails in Yahoo! Mail!
http://promo.yahoo.com/videomail/




******************************************
To post to the greenyes list,
email to: greenyes@grrn.org

Subscription information for
this list is available here:
http://www.grrn.org/general/greenyes.html
******************************************




******************************************
To post to the greenyes list,
email to: greenyes@grrn.org

Subscription information for
this list is available here:
http://www.grrn.org/general/greenyes.html
******************************************

[GreenYes Archives] - [Date Index] - [Thread Index]
[Date Prev] - [Date Next] - [Thread Prev] - [Thread Next]